Tutorials

By Jeff Mottle

Introduction to Gradient Ramp maps, 3D maps and blend material

Editor's notes

Article brought to you by Montree T.
Jeff Mottle — Founder at CGarchitect

Introduction to Gradient Ramp maps, 3D maps and blend materials

by Montree T. (easyyong@hotmail.com) - Smoke3dStudio



Gradient ramp

The Gradient Ramp is a 2D map similar to the Gradient map, however, the Gradient ramp can be shaded more than 3 and there are several different types of effects that this map can produce . The Gradient ramp can produce unbelivable effects when it is mixed with ifself and other maps. It's also easier to use gradient ramp tiling instead of using 2d maps.

There is not much explanation required for Gradient ramps, so just take a look at the example pictures below.


Gradient ramp: linear type

 
Single Linear   Tiling Linear


Example picture of a linear ramp type: This louvre example uses a linear gradient ramp on the diffuse and bump map channels.


Gradient ramp: box type

 
Single Box   Tiling Box


Example picture of the box type: assigned to bump and diffuse map channels


Gradient ramp: radial type

 
Single Radial   Tiling Radial



Example picture of the radial type: used as an opacity map

 

Gradient ramp: sweep type

 
Single Sweep   Tiling Sweep



Example picture of the sweep type: using sweep gradient ramp on the specular level map

 

Gradient ramp: Mapped type

The Mapped type is used for adding colors (or sub-maps) on a black and white map. The different values on a black and white map are replaced with the color on the gradient bar as the end result.


Example picture of mapped type masked by a black and white brick map. The shades of black are replaced with blue on the bar and the white is replaced with orange.


The end result of the gradient ramp: mapped type


Example of mapped type, colorful mosaic tile

Tips: Basically, I use gradient ramp as a mask map for a 2d mix map or blend material. It's an easier way to change the color of a map by using gradient ramp under a mix map rather than putting the color in gradient ramp itself (unless you have more than 2 color in your map).

Change the colors in the gradient ramp map itself.



Change the colors under mix map is easier

 

3D maps

Noise, dent, celular, specle, splatter and etc. I will skip defining these 3D maps as I assume that you have had some basic experience with them already. We simply use a single 3D map as a bump map, diffuse map etc.

The effect of a material that has more than two of these 3D maps with itself or other 2d map ie. gradient ramp, mixed together looks much better.

The example above shows a stone wall done with pure 3d cellular maps in several layers assigned to the diffuse, specular and bump maps. The rest of the materials on other objects are done with gradient ramp with 3D maps.

Another example with all materials created without any bitmaps. The rice is a cellular map and the meat is gradient ramp, and the plate uses noise and cellular maps.

 

Blend material

The Blend material is a mix of two independent materials with different shaders (can also be the same). The border of the two materials are specified by a black and white map that we call a "mask map". The first material in the blend slot refesr to the black color in the mask map and the second material refers to white. Both materials are overlaid in an area of the mask map which contains grey. I have a few examples which are practical to architectural rendering.

Example 1 : Creating a grid ceiling with a blend material.

From the picture, the material is composed of a grid area and diffuse light (fluorescent) which are specified by a mask map.

1. Mask map

I use a gradient ramp in black and white shade and a gradient type of box with 1x1 mirror tiling. The black in the mask map refers to grid ceiling area which is material 1 and the white is fluorescent area (material 2).




This is how the mask map look like.

2. Material 1


Material 1 (grid ceiling)

Go into material 1, which is thegrid ceiling. I use gradient ramp with box type again as a diffuse and bump map.

We also need to adjust the tiling of the grid which is now 3x3 mirror tiling to match with the mask map (1x1 mirror).

If the tiling numbers are diffirent from this sample, when you create a material on your own, the offset distance may also be changed to match with the tiling as well.

The example below shows a mismatched position of thetiling ,caused by the wrong adjustment on offset distance



3. Material 2


Material 2, fluorescent

Material 2 is fluorescent that is easy to create. I just change its self illumination parameter to 100 or color it white. If you want more detail on this fluorescent, you may add a gradient ramp map as its self illumination map.

I use 2 layers of gradient ramp to create this self illumination effect.






Grid Ceiling Chart



The ceiling in the image below is done with a blend material.





Example 2: Wet floor

Now that we have covered the blend material and using 2d gradient ramps, I hope you understand how to use them in your projects. The following example is for using 3d maps for a blend material that mostly needs no UVW map.

First, let me explain more about the legend of this material and its maps before we go onto the material chart.

The wet floor consists of 3 materials, mixed together which are:

1. Dry floor

Assign a 3d noise map to the the diffuse and bump channels. The shader is an Oren-Nayar-blinn type as I want the floor have roughness.

2. Damp floor

I just copy the dry material, but change specular level to be brighter, more glossy and make the diffuse color a bit darker as the damp floor contains a bit of water that makes its color darker. I then put in a little raytrace reflection.

3. Wet floor

This is the floor underneath the water. I still use the same material but change the specular and glossiness to be more glossy than the water. Remove Bump and add more reflection.

4. Mask map

As there are 3 basic materials (dry, damp and wet) there will be one more blend material that is overlayed on another blend material. I use 2 different dent maps (also 3d map) to specifiy the area of each material.


Mask 1


Mask 2





Below are 3d iamges,wet floor, using blend material



 




 

You must be logged in to post a comment. Login here.
likeddddddddddd
Excellent Work .... Really like the tips you shared ... want some more if possible ... Good Luck ! :-O)

About this article

Introduction to Gradient Ramp maps, 3D maps and blend material

visibility12.1 k
favorite_border6
mode_comment2
Report Abuse

About the author

Jeff Mottle

Founder at CGarchitect

placeCalgary, CA